Home > Usb Driver > Install Driver For Usb Cable

Install Driver For Usb Cable

Contents

Choose Prolific USB-to-Serial Comm Port Version: 3.2.0.0 and click NEXT. Click "Finish" to complete the installation. 7. I have tried loading this software as directed on both windows XP and windows 8 on two separate computers and I cannot get either radio to communicate with either computer. My best guess is the 1 mm ish metal ring on the bottom of the programming cable is not allowing it to seat deeply enough into the new versions of the this contact form

Using CHIRP. If the driver doesn’t install, run the following commands after replacing [Installation folder] with the actual installation path of the SMART education software. “Installation folder” refers to the path to where your This device cannot start. (Code 10) {Not Enough Quota} Not enough virtual memory or paging file quota is available to complete the specified operation. on 13 October 2011 02:18 PM Typical ELM327 USB Car Diagnostics Scanner This article will guide you how to install ELM327 USB cable/scanner on your Windows computer. http://smarttech.com/us/Support/Browse+Support/Support+Documents/KB4/170018.aspx

Usb Driver For Windows 7

Although I am not using a laptop but a normal windows7 PC. Right click on "Prolific USB-to-Serial Comm Port" and choose "Uninstall" b. If the driver isn’t found automatically, select Don't have a disc. To find and install the Baofeng USB Programming Cable driver and programming software correctly, follow the instructions below.

  1. Love this little radio.
  2. That is why you keep seeing 136.025 on the bottom display when you scroll through the channels on the top display.
  3. And yes, you can safely drive the vehicle while diagnosing it.
  4. Is there a difference that requires the use of a special cable for the UV82 or will the UV5R cable work just as good?
  5. I'm about to throw these Chinese radios away.

Can anyone help with this question?? Successfully downloaded the parameters that were on the UV B6. If the driver isn’t found automatically, select Don't have a disc. Usb Driver For Windows Xp Note that your submission may not appear immediately on our site.

Ron b | September 6, 2015 11:45 AM | Reply I took me all day to get both my BF-8HP programmed. After install, go to Step 2 to test it's working ok. — If you bought ELM327 cable from elsewhere (clones, eBay, other manufacturers) then install all Driver Packs below, because they Note that your submission may not appear immediately on our site. http://download.cnet.com/USB-Data-Cable/3000-18493_4-70481.html If anyone could help, I'd be grateful.

Step 3: Turn on car ignition. (One step before engine turns on) Step 4: Launch EasyOBD. Usb Drivers For Windows 7 Free Download Full Version HomeContact SupportKnowledgebaseDownloads Login Remember me Lost password Knowledgebase Driving Cycles (4) Downloads (9) General (48) Products Support (31) SEARCH Knowledgebase How to Install ELM327 USB Cable on Windows and OBD2 Software By Bernie ThompsonJuly 5, 201110 commentsInstalling, PL2303-DB9, Windowsamazon:asin=B00425S1H8, pl2303-db9, widget=pl2303-db9Windows 7 will detect and pop up a wizard to install drivers when our Plugable USB to Serial adapter is plugged in, Search HelpWhere to Buy Plugable USB to RS-232 DB9 Serial Adapter (Prolific PL2303HX Chipset) $14.95Select Market 1404followers3037likes8672subscribers383postsFollow us on TwitterMy TweetsSubscribe to Blog via EmailEnter your email address to subscribe to

Download Usb Driver For Windows 8

I added another repeater frequency to the table, uploaded the new parameters and the UV B6 showed the changes. well, I figured out the problem and wanted to share... Usb Driver For Windows 7 Any ideas ? Usb Driver Windows 10 I tried adding a new .csv file and using "save as" but that does nothing either.

I finally uninstalled my failed attempt through Windows Device Manager, restarted the computer and let the cable successfully install itself on my XP laptop and pc running Windows 7. weblink Happy New Year, Richard Rich n2kpr | January 3, 2014 5:25 PM | Reply Followed all your directions and still can't upload freq list. Check out our forum! Note: In the future, as long as you plug the USB cable into the same physical USB port, the cable will be assigned the same COM port number. Usb 2.0 Driver For Windows 7

If first 3 lines are not GREEN — refer to Common Solutions above. Gerry Eric | October 31, 2014 4:54 PM | Reply I read somewhere durng my exploits into programing my Baofeng GT-3 radio that you will use the UV-5r programing as the Look down the list of items for the "Ports" category and click the arrow to the left of "Ports" to expand the category. navigate here When I download from radio it ask me port I have tried /dev/cu.PL2303-0000201 and usb serial I have tired both ways and it comes up Cloning then it comes up An

Note 2: If the "Ports" category is not present, or the "Prolific USB-to-Serial..." device is not listed under "Ports," then click here. 3. Usb Driver Android Select Install.When updating the driver software is complete a dialog box appears saying, “Windows has successfully updated your driver software: SMART Board cable.”If the previous message doesn’t appear, run the following commands b.

Close see all reviews + Full Specifications+ General Publisher Fujitsu Publisher web site http://www.fujitsu.co.jp Release Date February 06, 2002 Date Added February 06, 2002 Version 1.2.5.0 Category Category Drivers Subcategory

Problem solver. Pros: (10 characters minimum)Count: 0 of 1,000 characters 4. Note the COM port must have "(in use)" listed next to it, if it does then another device with that name is already installed in the system. Install Usb Driver Windows 10 While my radio was communicating with the Baofeng software, it wouldn't with the CHIRP program.

Go to Troubleshooting below. Contact us nowTraining and professional development Explore our training and professional development offerings Browse our training offerings EN English Deutsch Francais Español ©2017 SMART Technologies - all rights reserved | Hope this is helpful. his comment is here Thanks for the instructions!

All Rights Reserved.Footer   Need answers and information? After a long and frustrating day using instructions from other websites written in Chinglish, I found yours. Remove the check from the box next to Allow the computer to turn off this device to save power and click Apply or Save. We carry the UV-5R but we do not have the UV-5RB, so we cannot guarantee the software we provide for the radios we sell will also work well for your particular

You can change these by double-clicking the USB-Serial adapter in Device manager, then selecting Port Settings from the Properties window that will open.I hope this helps.David Plugable Support Leave a Reply When cloning from the radio I still get the error "radio did not respond" Is there something else I need to do? I just purchased two more baofeng uv-b5 radios.When i try to program from my pc I get a error message that reads RADIO DID NOT ACK PROGRAMMING MODE!!! I have noticed the when I type in a save location it only changes the TX or RX that I am in.

If it was purchased from Buy Two Way Radios, it will come with the driver CD. Go to Step 2 below to test if everything is working ok... thanks joe Rick replied to comment from joe damiani | July 28, 2014 8:25 AM | Reply Hi Joe, if you tried everything in the instructions, you should already have the after changing all the tone modes it worked as normal.

Fortunately, there are other options available, and once properly installed, they are actually quite good.